I am well into my second heating season using your Vapor Fire 100 furnace, and I am so impressed! I live in central PA, and my home is about 25 years old. All other gasification furnaces I looked at all use a draft inducer fan, and have such a high output that would greatly exceed the needs of a home like mine. Your furnace is different. Using the lowest setting on the electronic control, I have been able to match the needs of my home very well.

The controller makes operating the furnace so easy, there was no learning curve. I build a small fire near the front of the furnace, and when it burns to coals, I just throw wood in and let the control take care of the rest. Typically I can have the furnace up to temperature in about 20 to 30 minutes after starting the starter fire. You can really see the electronic control's effect on the burn by watching the outgoing air temperature. When I run on low heat, my outgoing air temperature stays right at 127 degrees until there is no wood left, then it slowly drops. The BTU output really does stay constant as they claim.

Since the burn goes from front to back, I have found it to be really easy to hold a fire, even when warmer outdoor temperatures prevent me from filling the stove with wood. When the burn is done and the only hot coals are way in the back, they even stop glowing. It looks like the fire has completely gone out. When I rake these coals towards the front, closer to the air intake, they soon begin to glow to ignite the new wood.

This is definitely the safest wood burning stove I have ever owned. I have no fear of over-firing because I left the draft open too far.

If I had any doubts about how clean this stove burns, the proof came last spring when I removed the access plate to clean the area in the furnace where the flue gas goes after the secondary burn chamber. After burning a variety of different kinds of wood all winter long, I found only a thin layer of fine, grey dust. When I vacuumed it off, the steel looked brand new! There was no black creosote that needed to be scraped off! The walls of the secondary burn chamber were also clean!

Thanks for all your hard work on this product. It has made burning wood easy!

Fred Umble
New Holland, PA

Wood Gasification Kuuma VaporFire 100

Well it's all about safety, high efficiency, and enhancing our environment when it comes to burning wood using a VaporFire. "Smokeless" burns say it all...

The Vapor Fire 100 is our largest VaporFire. The wood length is approximately 20" and requires seasoned wood that has an 18-28% moisture content. It has a large 2-speed blower that delivers 500 to 1500 CFM (cublic feet per minute) on demand, controlled by a thermostat. It can stand alone as a central furnace, or be used as an add-on to an existing oil, gas, or electric furnace. The bonnet opening is 2'x2' and your heat duct outlet should be 180-200 square inches to prevent excess back pressure on the blower system. It gives you a clean, safe, and automatic front to back burn that delivers very even heat for 10-12 hours per load followed by many hours of coals. Even heat output results from the front to back burn principle in our VaporFires. It heats approximately 3500 square feet.


If you're on the fence please click on the following links to watch why our products are so efficient and unique...
Click Here to visit our YouTube page and watch videos of our products.
Click Here to visit our Facebook page.


Kuuma VaporFire Add-On (Or Central) Model 100

Vapor Fire 100
Pictured above is the Vapor Fire 100 with an overall efficiency rating of 83.5%

Why Choose a Kuuma VaporFire 100?

    No Visible Smoke up to 99% of the Time which means No Creasote
    No Catalytic Converters
    Logs Burn from the Front to the Rear
    Natural Burning of the Logs under Controlled Condition
    Fireboxes are under warranty for 25 years. With brick lining to the ceiling and ceramic lining behind the fire brick it is designed for a lifetime. All the internal parts are made with stainless steel and are replaceable.
    Furnace purchase includes both the barometric damper and firebricks


"Kuuma" principle - the logs burn from the front to the back. Primary air ignites only the amount of wood that will combust with the available oxygen within the fire chamber. Electronic control precisely regulates the amount of preheated air admitted into the fire chamber. Because the gases and volatile liquids burn at approximately 1000 degrees Fahrenheit it is important that the secondary air is preheated before it is introduced into the secondary zone. The fire burns with a nice soft low flame resulting in a highly efficient burn for a long period of time. You don't need a raging fire to produce a clean burn and useful heat.



VaporFire 100 Test Results



VF 100 Testing
VaporFire 100 being tested for efficiency at Intertek in Middleton, WI

Pricing

    The VaporFire 100 is $4,350.00 plus sales tax (Minnesota Residents)
    If the VaporFire 100 needs to be shipped there is a $50 crating fee on top of the variable shipping and handling charges for your area (please call and we can give an exact estimate).

VF 100 (Side)
Pictured above is a side view of VaporFire 100

Customer Testimonials


Real testimonials from our already satisfied customers...
If you already own one of our products and would like to express your thoughts, please send us an e-mail at lampmfg@gmail.com.
Click Here to visit our YouTube page and watch videos of our products.
Click Here to visit our Facebook page.

See Homemade Fresh Air Source Pictures
#1,#2,#3,#4,#5,#6,#7,#8,#9,#10



Lamppa Manufacturing Inc.

512 S. 3rd St.

Tower, MN 55790

(218) 753-2330 ,(800) 358-2049

lampmfg@gmail.com